-virginia Feed

Low..ri..der.. Take a little trip with me

IMG_2555
Thanks to a giagantus pot hole in DC, my old Italian buddy and commuter partner has been decimated beyond repair.  That's right, my Aprilia Scarabeo 250 has traveled it's last trek via a tow truck trailer to its final resting place, my house.  Thankfully, the pot hole only damaged my wheels and not me. But based on the rarity of parts and the age of the scooter (10 years), it isn't as cost effective for me run any more.   The wheels alone were going to run me over $500.  So once I find some replacement(used) parts I'll be selling the Beo.

However, after a few weeks as a metro bus/train commuter I started looking for another ride. The current scooter models just didn't have the same look I wanted as the Aprilia 'Beo, so I finally decided to expand into manual transmission territory.  Motorcycles.  It has been 25 years since I had a motorcycle, and that was a Yamaha 650 special that died more than it lived on the road.

Fast forward to me going through a refresher motorcycle course provided by a local Harley Davidson dealer, and I'm walking through their showroom looking for my new cycle.  My eye was drawn to the Sportster XL1200X, Forty-Eight immediately.  I test drove it with a Custom 1200 but knew that was the one I had my heart set on.

48

After buying my "48", I discovered the cycle was built seven days after my scooter had it's last ride. 

So, by the seventh day, the Harley builders finished the work they'd been doing; so on the seventh day, I could rest on a saddle seat and enjoy my ride!

IMG_2804
 


Project Underground: There's something on the wing!

All your base belong to dust
You're traveling through another dimension, a dimension not only of shoe molding and pneumatic-nailers but of miter saws.  A journey into a wondrous land whose baseboards are that of imagination. That's the sawhorse up ahead-your next stop, the Perimeter Zone!

Baseboards are something I take for granted until they start to show wear and tear.  When I started thinking about what to put in the basement, I had to look at what was already installed in the rest of the house to remember what I actually had.  The kind above came from Home Depot.

It took a little practice but pretty soon I had coping and miter cuts down, along with figuring out how to transitions trim over different floor heights. I had a bit of a floor drop along one wall, consisting of a tile and hardwood floors.  And another more radical change between the last step and my hardwood.  I like showing the transition.  Here's an example of how the cuts are made..

Baseboard miter cuts

Finished baseboard 1
Finished baseboard 2
So if you get the cracks just right, they'll be hidden with a little help from Spackle and paint. 

The inner and out corners were a little tricky.  But once I figured out how to do coping cuts for inner corners, it looked a lot better than trying to adjust a miter cut for a corner that wasn't perfectly square.  Here's someone else (HomeAdditionsPlus) showing how to make the cuts on YouTube. 

Unfortunately, you can't cut the outer corners like that.  I used a simple carpenter's protractor to measure the outer corner and divided the total to get the miter angle I needed.Protractor

All in all, I hadn't realized it was going to take a week just to run all the trim around the floor.  But after learning a few new tricks, I'm happy with the results. The dog on the other hand, she's just happy the floors are clean again.

Baseboard completed


Project Underground: splitting stairs

The day finally came for me to hand over my project to a third party contractor.  Instead of taking it one step at a time, I decided to have them do all twelve. (Ba-dum-bump..crash)

So I go from this fine pine leftover staircase with temporary landing...

Stairs1

Stairs2

To this...  Finished stairs 1
And these stalworth but ugly steps to...

Stairs3
this...

Finished stairs 2

I know what you're thinking.  Why is there a half wall of brick ramming this man's staircase?  Unfortunately, my sewer outlet pipe runs through it.  It's a bit off putting but after I finish the top of the half wall, it'll looks better.  And from the side as you look at the brick, it's worth it.

After the contractor finished the landing, I could see it wasn't exactly square.  So instead of shimming it out to square, the contractor just installed the hardwood.  So now the landing looks a little crooked if you look at it long enough. bummer..  But I did catch the contractor trying to install god awful brackets on the side. 

The brackets cover the profile of each tread and riser. (Note the gap for the last 5 steps in the picture above)  So with a little advice from B, I used my router and fabricated these.  Each step was not exactly the same height or length so it was truly a custom job.  I'm pretty happy with the results.

  Brackets

 

 


Now I can honestly say I've looked at every square inch of my floor..

IMG_2317
It took back to back weekends along with every weekday in between, but I was able to finally finish laying down all the engineered hardwood floor from Lumber Liquidators.  The color is gunstock oak and is 3/8" thick and 3" wide.  Schon is the manufacturer.

It took 8 boxes to finish a roughly 300 sq ft area.  I included about 10% for waste.  I had about 20 sq ft left over.

IMG_2332
I had to use a below grade engineered hardwood.  This variety wasn't a click and go version, so it took more time to glue all the slats together.  After a little planning I was able to come up with a random arrangement so all the joints were far enough apart.  You don't want the joints lining up too close otherwise the slats are not able to stay locked in overtime.

 IMG_2336
It went pretty smooth until I got closer to the stairway.  Then it was pretty obvious the framers hadn't made a square landing.  But I was able to adjust. Unfortunately, being a novice, that would come back to haunt me when the stairs were recapped.

IMG_2360
By the time I finished the floor, the chop saw was pretty broken in.  The last part to complete was under the stairway.  Next up, carpenters coming to do the stairs with real oak hardwood. 

 


Project Underground: Paint!

  Crayon-box-scr

Nothing says you're almost done with a remodel, like being ready to paint.  Unfortunately I tend to forget about what's left to do, such as: flooring, baseboards, trim, stairs, and a backsplash tile job that's still waiting in the wings.

But after consulting with B, the project designer, I narrowed the colors down to a couple I thought would work well together.  The plan would involve the largest wall being an accent wall and the rest of the basement being a more neutral color.  I'm going with a traditional flat white ceiling and semi-gloss white for all the trim/doors.

So I picked exclusive plum for the accent wall and emerging taupe for all the other walls.

What color does taupe look like?  The name reminds me of the crayons that no one liked.

Even after painting the walls, I was still on the fence. (I had tried a few sample spots, I still wasn't sure)   But I knew once it dried I'd get see the final look.   And the choices turned out great.  Living in a room with two colors is a first for me.  Looking forward to seeing how all the furniture will look once it's finished.

  

Paint1
Exclusive plum and emerging taupe come together

For those that notice what appears to be an outlet directly above the electric heater, that's actually a blank cover.  I removed the receptical after realizing the space heater was going to be too long to fit between the outlets.

Paint3
Brick and tile compared to the new paint

 

Paint3
FIOS, my fiber optic man servant, stops by to see how the painting is going.

 

 Next up - finishing the flooring!